FEATURES
- QoS Supports Layer 4
Classification
The switch supports not only Layer 2 802.1p Priority Queue
control, but also programmable higher layer classification and
prioritization, which enable enhanced Quality of Service (QoS)
supporting for real time applications based on information taken
from Layer 2 to Layer 4, such as VoIP.
- Port Mirroring Helps Supervisor
Monitoring Network
Port Mirroring copies traffic from a specific port to a target
port. This mechanism helps to track network errors or
abnormal packets transmission without interrupting the flow of
data.
- Q-in-Q VLAN For Performance &
Security
The VLAN feature in the switch offers the benefits of both
security and performance. VLAN is used to isolate traffic
between different users and thus provides better security.
Limiting the broadcast traffic to within the same VLAN broadcast
domain also enhances performance. VLAN supports enabling
advanced techniques such as "802.1 Q-in-Q" to be
deployed.
- 802.3ad LACP For Bandwidth
Aggregation
The Gigabit ports can be combined together to createa multi-link
load-sharing trunk. Up to 12 Gigabit ports can be set up per
trunk for bandwidth up to 24Gbps; all traffic is aggregated based
on MAC addresses, thus balancing the traffic load. The
switch supports up to 8 trunking groups. Port trunks are
useful for switch-to-switch cascading, providing very high
full-duplex speeds.
- 802.1x Access Control Improve
Network Security
802.1x feature enables user authentication for each network access
attempt. Port security feature allows you to limit the
numbers of MAC addresses per port in order to control the numbers
of stations for each ports. Static MAC addresses can be
defined for each port to ensure only registered machines are
allowed to access. By enabling both of these features, you
can establish an access mechanism based on user and machine
identities, as well as control the numbers of access stations.
- 802.1d Compatible & 802.1w
Rapid Spanning Tree
For mission critical environments with multiple switches
supporting STP, you can configure the switch with a redundant
backup bridge path, so transmission and reception of packets can
be guaranteed in event of any fail-over switch on the network.
- Broadcast/Multicast Storm Control
To limited too many broadcast/multicast packets flooding in the
network, the Broadcast/Multicast Storm Control is used to restrict
excess traffic. Threshold values are available to control
the rate limit for each port. Packets are discarded if the
count exceeds the configured upper threshold.
TECHNICAL SPECIFICATIONS
- Model: 5MGS2824G
- Standards: IEEE 802.3 / 802.3ab / 802.3z
/ 802.3u / 802.3x
- Connectors / Slots:
Front Panel
8 10/100/1000Mbps GbE RJ-45 auto MDI/MDI-X (Ports 1 to 8)
16 1000Mbps GbE SFP slots for fiber modules (Ports 9 to 24)
Rear Panel
1 RS-232 DB-9 Mail Console Port
[ Setting: Baud 57600, Data 8, Stop 1, Parity N, Flow NONE ]
- Add-on Modules (Sold Separately):
SFP.SX — 1000Base-SX Multi-Mode SFP
Duplex-LC, 850nm
SFP.L10 — 1000Base-LX
Single-Mode/10km SFP Duplex-LC, 1310nm
SFP.L40 — 1000Base-LX
Single-Mode/40km SFP Duplex-LC, 1310nm
- Data Transfer Rate:
10/100/1000Mbps (auto-negotiation or forced mode) for TP
1000Mbps for fiber
- Cable / Max Distance:
50/125, 62.5/125µm Multi-Mode fiber, 220m
9/125µm Single-Mode fiber, 10~70km (SFP module dependent)
Category 5 or up UTP, 100m for 100Base-TX and 1000Base-T
Category 3 or up UTP, 100m for 10Base-T
- Duplex Mode:
Full for 1000Base-SX/LX/T, and
Full/Half (auto-sense or forced-mode) for 10/100Base-TX
- MAC Address: 8K MAC addresses
- Flow Control:
IEEE 802.3x compliant for Full-duplex
Back pressure flow control for Half-duplex
- LEDs:
Unit — POWER, CPU
Per Port (TP/SFP) — LINK/ACT
- Power Requirement: 100~240V AC, 50/60Hz,
max 30W consumption
- Operating Temperature: 0° to 40° C
- Humidity: 5% to 90%
- Dimension:
44 x 442 x 209mm (H x W x D), 19" Rack-mountable with
brackets
- Safety: FCC Class A, CE Mark Approval,
RoHS Compliant
|
